Gw-instek GOS-6103C Manual do Utilizador

GOS-6103C OSCILLOSCOPE USER MANUAL  i  CONTENTS PAGE 1. PRODUCT INTRODUCTION...1-1.Description…

GOS-6103C OSCILLOSCOPE USER MANUAL  15  (13)CH1 VOLTS/DIV. (14)CH2 VOLTS/DIV– Control knob for channel 1/channel 2 has double function. Turnin

GOS-6103C OSCILLOSCOPE USER MANUAL  17  Horizontal controls: The horizontal controls select the time base operation mode and adjust the horizon

GOS-6103C OSCILLOSCOPE USER MANUAL  19  coefficient (uncalibrated i.e. “DLY>0.125ms”). The width of the window segment decreases when the DE

GOS-6103C OSCILLOSCOPE USER MANUAL  21  coefficient (reduce the deflection speed) and the deflection coefficient becomes uncalibrated. Instea

GOS-6103C OSCILLOSCOPE USER MANUAL  23  When the setting (voltage) value is out of the changing portion of the observation waveform, the synch

GOS-6103C OSCILLOSCOPE USER MANUAL  25  (30)DELAY-HO—Control knob with a double function and associated LED. The control knob has two different

GOS-6103C OSCILLOSCOPE USER MANUAL  27  Measurement and Panel setting Control The measurement section controls the on-screen readout and the cu

GOS-6103C OSCILLOSCOPE USER MANUAL  29  (34) MEMO- 9 —SAVE/RECALL The instrument contains 10 non-volatile memories, which can be used by t

GOS-6103C OSCILLOSCOPE USER MANUAL  31  4-2.Rear Panel The rear panel provides input power and additional signal connections. (39)Line volt

GOS-6103C OSCILLOSCOPE USER MANUAL  33  5. OPERATION METHOD This section contains basic operation information and techniques that should be con

GOS-6103C OSCILLOSCOPE USER MANUAL  iii  FOR UNITED KINGDOM ONLY NOTE: This lead/appliance must only be wired by competent persons WARNING: TH

GOS-6103C OSCILLOSCOPE USER MANUAL  35  5-2.Connecting Input Signals Grounding The most reliable signal measurements are made when the oscillos

GOS-6103C OSCILLOSCOPE USER MANUAL  37  7. Observe the displayed waveform and compare them with the waveforms shown in figure 5-2. If either p

GOS-6103C OSCILLOSCOPE USER MANUAL  39  4. Set both CH1 and CH2 COUPLING to GND. 5. Use the CH1 and CH2 POSITION controls to align both traces

GOS-6103C OSCILLOSCOPE USER MANUAL  41  Displaying the sum or difference of CH1 and CH2 To display the algebraic sum or difference of CH1 and C

GOS-6103C OSCILLOSCOPE USER MANUAL  43  Setting up Dual X-Y Operation To use the oscilloscope in the dual X-Y mode, proceed the following steps

GOS-6103C OSCILLOSCOPE USER MANUAL  45  Magnifying Waveform Events Use the ×10 MAG pushbutton to view small portions of a waveform as which is

GOS-6103C OSCILLOSCOPE USER MANUAL  47  Figure 5-12(a) TV-V Figure 5-12(b) TV-H The polarity of the synchronization pulse is critical for

GOS-6103C OSCILLOSCOPE USER MANUAL  49  Figure 5-14: Cursor Measurement (a).Typical △V (Voltage difference) for AC voltage. When both CH1 a

GOS-6103C OSCILLOSCOPE USER MANUAL  51  (g).Typical △Θcursor function for phase measurement. A phase measurement is done by first setting a r

GOS-6103C OSCILLOSCOPE USER MANUAL  53  6.MAINTENENCE The following instructions are executed by qualified personnel only. To avoid electrical

GOS-6103C OSCILLOSCOPE USER MANUAL  1  1.PRODUCT INTRODUCTION 1-1. Description The GOS-6103C is a 100MHz, two-channel, dual-sweep, portable os

GOS-6103C OSCILLOSCOPE USER MANUAL  55  7.Block Diagram

GOS-6103C OSCILLOSCOPE USER MANUAL  3  7) Trigger signal output The signal selected by the TRIGGER SOURCE is available. This output may be use

GOS-6103C OSCILLOSCOPE USER MANUAL  5  Horizontal Modes MAIN(A), ALT, DELAY(B) A (main) Sweep Time 50ns~0.5s/DIV, continuously variable (UNCA

GOS-6103C OSCILLOSCOPE USER MANUAL  7  3.PRECAUTIONS BEFORE OPERATION 3-1.Unpacking the Oscilloscope The product has been fully inspected and t

GOS-6103C OSCILLOSCOPE USER MANUAL  9  4. PANEL INTRODUCTION After the instrument is switched on, all the important settings are displayed in t

GOS-6103C OSCILLOSCOPE USER MANUAL  11  4-1.Front Panel Display controls The display controls adjust the on-screen appearance of the waveform a

GOS-6103C OSCILLOSCOPE USER MANUAL  13  (7).20MHz BWL – Pushbutton with indicator LED. Briefly pressing the pushbutton, the bandwidth is reduce