Gw-instek PEL-3000 Series User Manual Manual do Utilizador

DC Electronic Load PEL-3000 Series USER MANUAL VERSION: 1.14 ISO-9001 CERTIFIED MANUFACTURER

PEL-3000 User Manual 8 GETTING STARTED This chapter provides a brief overview of the PEL-3000, the package contents, instructions for first time u

PEL-3000 User Manual 98 4. Repeat step 3 for any remaining programs in the chain. 5. Press Save to save the program chain to internal memory.

OPERATION 99 5. When a program/chain has finished running, a list of the Go-NoGo results for each step are displayed.  Press Exit[F5] to exit. D

PEL-3000 User Manual 100 Sequence The PEL-3000 supports both programs and sequences. The essential difference between programs and sequences is t

OPERATION 101 Sequence 1STEP 01STEP 02:STEP NSequence 2STEP 01STEP 02:STEP NSequence 10STEP 01STEP 02:STEP N Start Sequence: ::: Description Norm

PEL-3000 User Manual 102 Memo 12 characters A user-created note for the currently selected sequence. Mode CC, CR, CV, CP Operating mode for the se

OPERATION 103 RAMP ON, OFF When turned on the current transition is evenly ramped from the start of the step to the end of the step. When turned off

PEL-3000 User Manual 104 PAUSE ON, OFF Pause: Inserts a pause at the end of the step. When paused, the unit will pause at the end of the step curr

OPERATION 105 4. Set the following parameters for the currently selected sequence. See page 100 for details on each parameter.  Memo  Mode 

PEL-3000 User Manual 106 Data Edit Configuration Data Edit Display PreviousMenuLOADRS23203/Sep/2012Data Edit for Normal SequencesRAMP:LOAD:OFFOF

OPERATION 107 5. Set the following parameters for the currently selected step. See the Data Edit Overview on page 102 for configuration details. 

GETTING STARTED 9 (PEL-3211 Booster Pack) ... 21 Display ...

PEL-3000 User Manual 108 Running a Normal Sequence Description A load created with the Normal Sequence function is run the same way as a normal l

OPERATION 109 Display: Sequence/Chain Running ContinueNSEQRS23203/Sep/2012Run N.Seq.0.000V0.000A0.00wStepSeq. No: 01Loop: 00010003

PEL-3000 User Manual 110 Fast Sequence Overview Description A fast sequence is comprised of a user-defined number of steps that can be executed a

OPERATION 111 Description Fast Sequence configuration is split into Timing Edit configuration and Data Edit configuration. Timing Edit configuratio

PEL-3000 User Manual 112 Data Edit Overview Each step in a fast sequence contains the following setting parameters: Setting Setting Range De

OPERATION 113 range. Value settingStep 02Step 4Step 01StepFILL exampleStep 03End_ValueStart_Value Filled values Filled steps Start_Step End_Step

PEL-3000 User Manual 114 Timing Edit Configuration Edit Timing Display PreviousMenuLOADRS23203/Sep/2012Timing Edit for Fast SequenceLoop:Range:M

OPERATION 115 Sequence Timing configuration is complete.  Go to Data Edit to edit the steps used in the Fast Sequence. Page 115.  Go to Runni

PEL-3000 User Manual 116 2. Press Insert Point[F1] to add a step to the sequence.  Every-time Insert Point is pressed the Step parameter is in

OPERATION 117 Save After all the steps for the sequence are complete, press Save[F3] to save the steps. Data Edit for Fast Sequences configuration

PEL-3000 User Manual 10 PEL-3000 Series Introduction The PEL-3000 Series is a family of high performance DC electronic loads positioned to test a

PEL-3000 User Manual 118 Display: Fast Sequence Running FSEQRS23203/Sep/2012Run F.Seq.0.998V153.10mA0.1528wStepLoop: 00010023Current loop numberCu

OPERATION 119 Save Recall The PEL-3000 can save and recall system settings, preset data, memory data, Go-NoGo settings as well as normal and fast s

PEL-3000 User Manual 120 For example: To load Preset Data P7 from USB, you must first load Preset Data P0~P9 to internal memory, then from inter

OPERATION 121 Preset Data Preset Data contains the same settings as the Memory Data. Preset Data contains the operating mode, range, response and Go

PEL-3000 User Manual 122 Memory Data Example Active settingM001::M256 MXXXMedia | Memory Display SaveData Type MemoryRS23203/Sep/2012Memory M256A

OPERATION 123 Note Normal Sequence and Fast Sequence data cannot be recalled from or saved to an internal memory slot. Saving Files to USB Memory

PEL-3000 User Manual 124 Operation 1. Insert a USB drive into the USB port. 2. Press Shift + FileFUNC. 3. Select USB with the Media[F1] soft-ke

OPERATION 125 Recalling Files from Internal Memory Description When recalling Memory, Setup or Preset Data from the internal memory slots, the reca

PEL-3000 User Manual 126 4. Select which memory slot to recall from. Memory: Setup Memory: Preset: M001 ~ M256 1 ~ 100 P0 ~ P9 5. Press Recal

OPERATION 127 Memory Data Example Media | USBMedia | MemoryRecall fileM001::M256 MXXX For example, if the file 3021_01.M is recalled, all the Memor

GETTING STARTED 11 Main Features Performance  High slew rates of up to 16A/μS(PEL-3111) for a fast response speed  High capacity when used in p

PEL-3000 User Manual 128 Memory: Setup Memory: Preset: NSeq: FSeq: Model_file number.M Model_file number.S Model_file number.P Model_file number.

OPERATION 129 Note This setting only applies when recalling preset settings from internal memory, either by using the Presets keys (P0 ~ P9) or by

PEL-3000 User Manual 130 Rename a Folder 1. Use the scroll wheel to move the cursor to the file/folder you wish to rename. 2. Press Rename[F3].

OPERATION 131 Quick Preset Recall Description Presets P0 to P9 can be recalled quickly by using the Preset key and the number pad. Operation 1. Pr

PEL-3000 User Manual 132 User’s Default Setting Description The currently active settings can be set as the ―User’s Default‖ settings. Save User’

EXTERNAL CONTROL 133 EXTERNAL CONTROL Analog Control ... 134 J1 Connector Overview ...

PEL-3000 User Manual 134 Analog Control The Analog Control subsection describes how to use the J1 Frame Control Connector for voltage or resistanc

EXTERNAL CONTROL 135 External Voltage Control - Overview Background External voltage control of the CC, CR, CV and CP mode is accomplished using th

PEL-3000 User Manual 136 Caution When using external voltage control, make sure no more than ±11V is applied across pins 1 and 3. Exceeding this

EXTERNAL CONTROL 137 CR Mode Input conductance = rated conductance × (external voltage/10) Input ConductanceExternal VoltageRated Conductance0V 10V

PEL-3000 User Manual 12 Accessories Standard Accessories Part number Description 82EL-31110MB1 Quick Start Guide 82EL-31110EB1 User / Program

PEL-3000 User Manual 138 3. Turn the power on the PEL-3000. 4. Set the operating mode and range.  See page 51 for CC mode.  See page 53 fo

EXTERNAL CONTROL 139 Connection When connecting the external resistance source to the J1 connector, use a ferrite core and use twisted pair wiring.

PEL-3000 User Manual 140 External Resistance Control – Operation Description External resistance control can be used to control the current, volt

EXTERNAL CONTROL 141 CR Mode Proportional Control: Input conductance = rated conductance × (external resistance/10). Inverse Control: Input conduct

PEL-3000 User Manual 142 CP Mode Proportional Control: Input power = rated power × (external resistance/10). Inverse Control: Input power = rated

EXTERNAL CONTROL 143 5. Press Main > Configure [F5] > Next Menu [F4] > External [F3]. 6. Set the Control to R for proportional control or

PEL-3000 User Manual 144 Example The LoadOn IN setting determines whether the load is turned on when the external switch is closed (low) or open (

EXTERNAL CONTROL 145 Load On/Off Status Description Pin 13 (Load On Status) of the J1 connector is used to monitor the load status (on or off). P

PEL-3000 User Manual 146 Pin Inputs Pins 8 and 9 of the J1 connector are internally pulled up to 5V with a 10kΩ resistor when open. When closed, p

EXTERNAL CONTROL 147 Pin out The Range Status pins are photo-coupled open-collector outputs. 1714, 15 Photocoupler input: 30V max, 8mA, max. Exter

GETTING STARTED 13 GTL-255 300mm Frame Link Cable (for linking units that are stacked) GTL-248 GPIB cable, 2.0m GTL-246 USB cable, Type A - Type

PEL-3000 User Manual 148 External Control of the Alarm Description An alarm can be activated/deactivated using external control with the J1 conne

EXTERNAL CONTROL 149 Alarm Status Description Pins 16 and 17 of the J1 connector are used to monitor whether the alarm is on or off. Pin out The A

PEL-3000 User Manual 150 Monitor Signal Output Trigger Signal Output Description The trigger output signal is generated every time a switching op

EXTERNAL CONTROL 151 settings. CurrentIMON VRated Current Monitor Output Range Monitor Connector Current Range Monitor Output Range I MON OUT (B

PEL-3000 User Manual 152 Parallel Operation The PEL-3000 series can be connected in parallel to increase the total power capacity of a single unit

EXTERNAL CONTROL 153 Parallel Capacity, PEL-3211 Model No. of Units V I Total Sink Current PEL-3111 + PEL-3211 Total Power PEL-3111 + PEL-3211 P

PEL-3000 User Manual 154 MASTER+-+S-SSLAVE 1+-+S-S+-+S-SSLAVE 2+-+S-SDUT-+J2J1J2J1J2J1J2J1SLAVE 3Load wiringFrame link cable(GTL-255)Sense wiring

EXTERNAL CONTROL 155 Configuration Description When using the multiple units in parallel all the basic settings are adopted from the master unit. O

PEL-3000 User Manual 156  A maximum of 5 units can be used in parallel.  A maximum of 4 boosters can be used with a single PEL-3111, acting as

EXTERNAL CONTROL 157 Turning the Load On Description Operating the PEL-3000 Series in parallel mode is the same as for single units. Note When u

PEL-3000 User Manual 14 Package Contents Check the contents before using the instrument. Opening the box Contents (single unit)  Main

PEL-3000 User Manual 158 Disable Parallel Mode Description To disable parallel mode, each unit must be set as a ―Master‖. Operation 1. Turn the

REMOTE CONTROL 159 REMOTE CONTROL This chapter describes basic configuration of IEEE488.2 based remote control. For a command list, refer to the pro

PEL-3000 User Manual 160 Interface Configuration Configure to USB Remote Interface USB configuration PC side connector Type A, host PEL-3000 side

REMOTE CONTROL 161 2. Connect a GPIB cable from a GPIB controller to the GPIB port on the PEL-3000. 3. Turn the PEL-3000 on. 4. Press Shift + Ut

PEL-3000 User Manual 162 Configure RS232C RS232C Configuration Connector DB-9, Male Baud Rate 2400, 4800, 9600, 19200, 38400 Stop Bit 1, 2 Parit

REMOTE CONTROL 163 RS232C/USB Remote Control Function Check Functionality check Invoke a terminal application such as Realterm. For RS-232C, set t

PEL-3000 User Manual 164 Using Realterm to Establish a Remote Connection Background Realterm is a terminal program that can be used to communic

REMOTE CONTROL 165 If using USB, the baud rate, stop bit and parity settings can be viewed by right-clicking connected device and selecting the Prop

PEL-3000 User Manual 166 6. After Realterm has started, click on the Port tab. Enter the Baud, Parity, Data bits, Stop bits and Port number conf

REMOTE CONTROL 167 7. Click on the Send tab. In the EOL configuration, check on the +CR and +LF check boxes. Enter the query: *idn? Click on Send

GETTING STARTED 15 Appearance PEL-3000 Front Panel (PEL-3021/PEL-3041) I MON OUT TRIG OUT1.5 - 150V175W0 - 35AP0P1P4P7CAL.P2P5P8LockP3P6P9UtilityL

PEL-3000 User Manual 168 GPIB Function Check Functionality check Please use the National Instruments Measurement & Automation Controller so

REMOTE CONTROL 169 3. Press the Scan for Instruments button. 4. In the Connected Instruments panel the PEL-3000 should be detected as Instrument

PEL-3000 User Manual 170 678 9. The function check is complete.

FAQ 171 FAQ • The load voltage indicated on the load module is below expected. • The front panel keys are not working. • The load won’t turn on. •

PEL-3000 User Manual 172 For more information, contact your local dealer or GWInstek at www.gwinstek.com / [email protected].

APPENDIX 173 APPENDIX Replacing the Dust Filter ... 175 Replace the Clock Battery ...

PEL-3000 User Manual 174 Other ...

APPENDIX 175 Replacing the Dust Filter Background The dust filter should be replaced twice a year. Not replacing the filter will reduce performance

PEL-3000 User Manual 176 Replace the Clock Battery Background The system clock keeps time using a user-replaceable battery. The battery should be

APPENDIX 177 GPIB Installation Background GPIB is an optional extra. The following instructions describe how to install the optional GPIB card if n

PEL-3000 User Manual 16 (PEL-3211 Booster Pack) LINK STBY Air Inlet The air inlet has a removable dust filter LCD display 3.5 inch LCD display Fu

PEL-3000 User Manual 178 PEL-3000 Default Settings The following default settings are the factory configuration settings for the PEL-3000. Main S

APPENDIX 179 Main > Configure > Other Item Panel Settings Setup Memory Settings (all 100 sets) Soft Start OFF OFF Von Voltage 0.00V 0.00V Von

PEL-3000 User Manual 180 Main > Configure > Next Menu > Knob Item Panel Settings Setup Memory Settings (all 100 sets) Status Step Step CC

APPENDIX 181 Frame Control Connector Contacts J1 Connector Pin name Pin number Description EXT R/V CONT 1 Used for voltage/resistance control of CC

PEL-3000 User Manual 182 TRIG INPUT 11 When paused, clears the pause when a low level TTL signal is applied for 10 μs or longer. Pulled down the i

APPENDIX 183 J2 Connector Pin name Pin number Description N.C. 1 N.C. 2 N.C. 3 SUM I MON 4 Connect to SUM I MON of the J1 connector. PRL OUT+

PEL-3000 User Manual 184 SUM I MON 4 Connected to SUM I MON of the J2 connector. PRL IN+ 5 Connected to PRL OUT+ of the J2 connector. PRL IN- 6 Co

APPENDIX 185 J2 Connector Booster Pin name Pin number Description N.C. 1 N.C. 2 N.C. 3 SUM I MON 4 Connect to SUM I MON of the J1 connector. PRL

PEL-3000 User Manual 186 Operating Mode Description CC Mode CC Mode When the unit is set to CC mode it will operate as a constant current load wh

APPENDIX 187 CC + CV ModeLoad InputVoltageLoad CurrentCV levelCC Current Value Note that when the source voltage is less than the CV level, no curre

GETTING STARTED 17 FileFUNCShift File (Shift + FUNC): Accesses the file system. Help/Utility Help Help: Access the help menu. UtilityHelpShift Uti

PEL-3000 User Manual 188 CR+CV Mode When CR+CV mode is enabled, the unit will act as constant resistive load after the input voltage is greater th

APPENDIX 189 CP ModeLoad CurrentLoad InputVoltageCP Value CP+CV Mode When CP+CV mode is enabled, the unit will act as a constant power load after th

PEL-3000 User Manual 190 CV Mode CV Mode When the unit is set to CV mode it will operate as a constant voltage load when connected to a constant

APPENDIX 191 Operating Area PEL-3021

PEL-3000 User Manual 192 PEL-3041

APPENDIX 193 PEL-3111

PEL-3000 User Manual 194 PEL-3211 Booster Pack

APPENDIX 195 PEL-3000 Specifications The specifications apply when the PEL-3000 is powered on for at least 30 minutes to warm-up to a temperature of

PEL-3000 User Manual 196 CC Mode Model PEL-3021 PEL-3041 PEL-3111 Operating Range H Range 0A~35A 0A~70A 0A~210A M Range 0A~3.5A 0A~7A 0A~21A L Ra

APPENDIX 197 CR Mode Model PEL-3021 PEL-3041 PEL-3111 Operating Range*1 H Range 23.3336S~400uS (42.857mΩ~2.5kΩ) 46.6672S~800uS (21.428mΩ~1.25kΩ) 14

This manual contains proprietary information, which is protected by copyright. All rights are reserved. No part of this manual may be photocopied,

PEL-3000 User Manual 18 Number pad P0P1P4P7CAL.P2P5P8LockP3P6P90147258369Clear Number pad: Used to enter numerical values. P0~P9 (Preset + Numbe

PEL-3000 User Manual 198 Setting Range H Range 0V~157.5V M Range 0V~15.75V Resolution H Range 10mV M Range 1mV Accuracy of Setting*1 H, L Range ±(

APPENDIX 199 Slew Rate Model PEL-3021 PEL-3041 PEL-3111 Setting Range (CC Mode) H Range 2.5mA/us~2.5A/us 5mA/us~5A/us 16mA/us~16A/us M Range 250uA/

PEL-3000 User Manual 200 Ammeter H, M Range 0.000A~35.000A 0.000A~70.000A 0.00A~210.00A L Range 0.00mA~350.00mA 0.00mA~700.00mA 0.0mA~2100.0mA Acc

APPENDIX 201 Slew Rate Setting Range (CR Mode) H Range 250uA/us~250mA/us 500uA/us~500mA/us 1.6mA/us~1.6A/us M Range 25uA/us~25mA/us 50uA/us~50mA/us

PEL-3000 User Manual 202 Resistance Accuracy of setting H, M Range ±(0.5 % of set*1 + 0.5 % of f.s*2) + Vin*3/500 kΩ L Range ±(0.5 % of set*1 + 0.

APPENDIX 203 Protection Function Model PEL-3021 PEL-3041 PEL-3111 Overvoltage protection(OVP) Turns off the load at 110% of the rated voltage Over

PEL-3000 User Manual 204 Fast Sequence Operation mode CC or CR Maximum number of steps 1000 Step Execution Time 25 μs – 600 ms Time resolution 1u

APPENDIX 205 Range Switch Input Switch ranges L, M, and H using a 2-bit signal Range Status Output Outputs range L, M, or H using 2-bit signal (op

PEL-3000 User Manual 206 Front Panel BNC Connector TRIG OUT Trigger output: Approx. 5V pulse width: Approx. 2 μs, output impedance: Approx. 500

APPENDIX 207 PEL-3000 Dimensions PEL-3111 P0P1P4P7CAL.P2P5P8LockP3P6P9UtilityLocalFile0147258369EnterClearShiftPresetLoadOn/OffMainHelpFUNCShortTRI

GETTING STARTED 19 Front panel input terminals 1.5 - 150V175W0 - 35A Negative terminal. Positive terminal. IMON Out I MON OUT Current monitor BNC

PEL-3000 User Manual 208 PEL-3021, PEL-3041 I MON OUT TRIG OUT1.5 - 150V175W0 - 35AP0P1P4P7CAL.P2P5P8LockP3P6P9UtilityLocalFile0147258369Enter

APPENDIX 209 PEL-3211 PEL-3211DC Electronic Load0 - 420A / 1.5 - 150V , 2100WLINK STBY427.75.05.8553.5592.5127.8147.8

PEL-3000 User Manual 210 Declaration of Conformity We GOOD WILL INSTRUMENT CO., LTD. No. 7-1, Jhongsing Rd, Tucheng Dist., New Taipei City 236, T

INDEX 211 INDEX Accessories ... 12 Advanced configuration Alarm tone ... 87 Auto Loa

PEL-3000 User Manual 212 Knob configuration Cursor ... 77 Step ...

INDEX 213 About disassembly ... 4 Contact ... 172 Setting the date and time ... 2

PEL-3000 User Manual 20 Rear Panel PEL-3021 / PEL-3041 47 - 63 Hz90 VA MAX.AC100 - 120 VAC200 - 240 VACFRAME CONTJ 1J 2SER. NO. LBRS232CGPIBWAR

GETTING STARTED 21 (PEL-3211 Booster Pack) RS232C Port GPIB USB B The USB B, RS232C and GPIB port are used for remote control. USB B port RS

PEL-3000 User Manual 22 Exhaust fan The exhaust fan is used to expel the heat from the unit. Please ensure there is at least 20cm distance between

GETTING STARTED 23 Display ModeCVI RangeH 35AV RangeL 15VFunctionStaticConfigure0.000V0.000A0.00wSlewRate 2500.00CC B Value 0.000CC A Value 0.000LOA

PEL-3000 User Manual 24 First Time Use Instructions Use the procedures below when first using the PEL-3000 to install the rack mount kit, power up

GETTING STARTED 25 GRA-413 (EIA standard) 128532.5482.6 GRA-413 (JIS standard) 149532.5482.6

PEL-3000 User Manual 26 GRA-414-E (EIA standard) 132382.5477.6 GRA-414-J (JIS standard) 149382.5477.6

GETTING STARTED 27 Power Up and Self Test Steps 1. Insert the AC power cord into the power socket. 2. Turn the external power switch on. (O →

Table of Contents 1 Table of Contents SAFETY INSTRUCTIONS ... 3 GETTING STARTED ...

PEL-3000 User Manual 28 Load Default Settings Description When first using the PEL-3000, recall the factory default settings to ensure the unit

GETTING STARTED 29 SystemInfoLoad Interface Time Set LOADRS23203/Sep/2012 Other9Hour 0Year 2012MinuteDayMonth93Date/TimeDate Load Wiring Wire Gau

PEL-3000 User Manual 30 2 6.54304 0.51266 181 3 5.82676 0.64616 158 4 5.18922 0.81508 135 5 4.62026 1.02762 118 6 4.1148 1.29593 101 7 3.665

GETTING STARTED 31 CurrentVoltagetimetime∆I∆TEMin. V The diagram above shows how changes in current can affect voltage. Limiting Load line induct

PEL-3000 User Manual 32 Load Wire Connections Description The PEL-3000 has input terminals on both the front and rear panels. Follow the procedur

GETTING STARTED 33 Using the Front Panel Input Terminals Description The front panel input terminals feature polarity-distinct caps and accept M6 s

PEL-3000 User Manual 34 Using the Rear Panel Input Terminals Description The rear panel input terminals accept up to M8-sized crimped terminals.

GETTING STARTED 35 Using the Terminal Cover Description The rear panel terminal cover should be used to prevent electric shock. The rear panel term

PEL-3000 User Manual 36 2Detail3 4. Use your thumb to slide the terminal covers shut, as shown in the diagram below. 4

GETTING STARTED 37 5. When the top and bottom covers are flush, reinsert the screw that was removed in step 1. 5

PEL-3000 User Manual 2 Replace the Clock Battery ... 176 GPIB Installation ... 177 PEL-3000 Default S

PEL-3000 User Manual 38 Remote Sense Description Remote sense can be used to help compensate for long cable length. The longer the cable, the hig

GETTING STARTED 39 Firmware Update Description The PEL-3000 allows the firmware to be updated by end-users. Before using the PEL-3000, please check

PEL-3000 User Manual 40 SystemInfoLoad Interface Time Set LOADRS23203/Sep/2012Model : PEL-30XX Firmware Ver. : 1.01.011Serial Number : 00000001O

GETTING STARTED 41 Conventions The following conventions are used throughout the user manual. Read the conventions below for a basic grasp of how to

PEL-3000 User Manual 42 Toggle Parameter or State ModeCCFunction/ItemParameter or State This type of soft-menu icon has the function/item on the t

GETTING STARTED 43 Parameter Input The scroll wheel, Enter key and number pad can be used to edit parameter values. Number padScroll wheelEnter key

PEL-3000 User Manual 44 3. Then use the number pad* or scroll wheel** to edit the parameter value. ModeCCI RangeH 35AV RangeL 15VFunctionStati

GETTING STARTED 45 Step Mode: This is the default step resolution method and will only be available to use when it is applicable (Indicated by Fine

PEL-3000 User Manual 46 Entering Alphanumeric Characters When renaming files, creating memos or notes, you will be required to enter alphanumeric

GETTING STARTED 47 Help Menu When any function key has been pressed or when a menu has been opened, the HELP key can be used to display a detailed d

SAFETY INSTRUCTIONS 3 SAFETY INSTRUCTIONS This chapter contains important safety instructions that you must follow during operation and storage. R

PEL-3000 User Manual 48 OPERATION Basic Operation ... 51 CC Mode ...

OPERATION 49 Cursor Mode Configuration ... 77 Step Mode Configuratio

PEL-3000 User Manual 50 File Types ... 120 Saving F

OPERATION 51 Basic Operation The PEL-3000 supports 7 main operating modes: CC, CC+CV; CR, CR+CV; CV; CP, CP+CV CC Mode Description In Constant Cu

PEL-3000 User Manual 52 6. Set the current level parameters using the scroll wheel and number pad.  For Static mode, set CC A Value and/or CC

OPERATION 53 CR Mode Description In Constant Resistance Mode, the unit will maintain a constant resistive load by varying the current. CR mode use

PEL-3000 User Manual 54 6. Set the resistance or conductance level parameters using the scroll wheel and number pad.  For Static mode, set CR

OPERATION 55 CR Units Description The CR setting units can be set to ohm (Ω) or millisiemens (mS). Operation 1. Make sure the load is off. 2. P

PEL-3000 User Manual 56 6. Set the voltage level parameters using the scroll wheel and number pad.  Set CV A Value and/or CV B Value.  The

OPERATION 57 Warning If you change the mode or the range when the load is already on, the load will be turned off automatically. Operation 1. Mak

PEL-3000 User Manual 4 Safety Guidelines General Guideline CAUTION  Do not place any heavy object on the instrument. Note: Only 2 units can be

PEL-3000 User Manual 58 Display ModeCPI RangeH 35AV RangeH 150VFunctionStaticConfigure0.00V0.000A0.00wCP B Value 0.00CP A Value 0.00LOADRS232A Val

OPERATION 59 Display ModeCPI RangeH 35AV RangeL 15VFunctionDynamicConfigure0.000V0.000A0.00w+CV 5.500Timer2 0.025Timer1 0.025LOADRS23203/Sep/2012Vms

PEL-3000 User Manual 60 Note  The load can be set to automatically turn on at start up. See page 75.  The load can be turned on via remote co

OPERATION 61 Operation 1. The short function can be turned on and off by pressing the Short key.  The Short key will turn red when the short func

PEL-3000 User Manual 62 Operation 1. The keys can be locked and unlocked by pressing Shift+LockClear.  LOCK will appear in the Mainframe status

OPERATION 63 Basic Configuration The basic configuration settings are the common configuration settings that are used for each operating mode. After

PEL-3000 User Manual 64 LevelTimeLevel 2Level 1Timer1 Timer2 Timer1Dynamic Mode Note Dynamic mode is not available for CV mode. Operation 1. Mak

OPERATION 65  The load can be ―on‖ when switching between A Value and B Value. Display: Static Mode ModeCPI RangeH 35AV RangeH 150VFunctionSt

PEL-3000 User Manual 66 Operation 1. Make sure the load is off. 2. Press Main > Configure[F5] > Other[F2] and set the Dyna. Level setting

OPERATION 67 Select the Switching Time Configuration for Dynamic Mode Description The switching time for dynamic mode can be configured to switch b

SAFETY INSTRUCTIONS 5 Power Supply WARNING  AC Input voltage range: 100~120VAC/200~240VAC (90~132VAC/180~250VAC)  Frequency: 47~63Hz  Power:

PEL-3000 User Manual 68 Display ModeCCI RangeH 35AV RangeH 150VFunctionDynamicConfigure0.00V0.000A0.00wTimer1 0.025SlewRate 2500.00SlewRate 2500.0

OPERATION 69 Display ModeCVI RangeH 35AV RangeL 15VResponseSlowConfigure0.000V0.000A0.00wCV B Value 15.000CV A Value 15.000LOADRS232A ValueFine03/Se

PEL-3000 User Manual 70 Advanced Configuration Settings Use the advanced configuration settings to configure settings other than those described i

OPERATION 71 Von Voltage Settings Von Voltage Level Description The Von Voltage is the threshold voltage at which the load module will start to sin

PEL-3000 User Manual 72 Von Voltage Latch Description When Von Latch is set to ON, the load will continue to sink current after being ―latched‖,

OPERATION 73 Von Voltage Delay Description Von Delay is the amount of time the unit will wait before turning the load on after the Von Voltage thre

PEL-3000 User Manual 74 Operation 1. Press Main > Configure[F5] > Other[F2] and turn the Count Time on or off. Range: ON, OFF Display Mo

OPERATION 75 Auto Load Configuration Description The PEL-3000 can be configured to automatically load the last program, normal sequence, fast seque

PEL-3000 User Manual 76 Load Off (Mode) and Load Off (Range) Description By default the load will automatically turn off when the either the oper

OPERATION 77 Step Resolution Configuration There are two different ways to set the set resolution when using the scroll wheel to edit parameters. St

PEL-3000 User Manual 6 (Pollution Degree) EN 61010-1:2010 specifies the pollution degrees and their requirements as follows. The instrument falls

PEL-3000 User Manual 78 Step Mode Configuration Description When set to Step Mode, the voltage, current, resistance and power settings can have t

OPERATION 79 Operation 1. Press Main > Configure[F5] > Next Menu[F4] > Knob[F2] and make sure the Status setting is set to Step. 2. Set t

PEL-3000 User Manual 80 Protection Settings The Protection settings are used to prevent damage to the unit or the DUT by excessive current, voltag

OPERATION 81 Display 2.596V500.06mA1.2982wCV B Value 15.000CV A Value 15.000LOADRS232A ValueFine03/Sep/2012VVOCP AlarmPlease Press EnterTo Clear Ala

PEL-3000 User Manual 82 Display 2.596V500.06mA1.2982wCV B Value 15.000CV A Value 15.000LOADRS232A ValueFine03/Sep/2012VVOPP AlarmPlease Press Ente

OPERATION 83 Display 2.596V500.06mA1.2982wCV B Value 15.000CV A Value 15.000LOADRS232A ValueFine03/Sep/2012VVUVP AlarmPlease Press EnterTo Clear Ala

PEL-3000 User Manual 84 Display 2.596V500.06mA1.2982wCV B Value 15.000CV A Value 15.000LOADRS232A ValueFine03/Sep/2012VVOVP AlarmPlease Press Ente

OPERATION 85 Para Description The Para error message will appear on the display when the PEL-3000 is used in parallel and if an error is produced.

PEL-3000 User Manual 86 System Settings The following section covers a number or miscellaneous system settings such as:  Speaker settings  Dis

OPERATION 87 Alarm Tone Settings Description The alarm tone for the unit can be turned on or off in the utility menu. The alarm tone can be set sep

SAFETY INSTRUCTIONS 7 Power cord for the United Kingdom When using the instrument in the United Kingdom, make sure the power cord meets the followin

PEL-3000 User Manual 88 Control Settings Description The Knob Type setting determines if values are updated immediately as they are edited or if

OPERATION 89 Go-NoGo The Go-NoGo configuration is used to create pass/fail limits on the voltage or current input. If the voltage/current exceeds t

PEL-3000 User Manual 90 5. Set the Delay Time.  The delay time setting will delay activating the Go-NoGo testing by a specified amount of time

OPERATION 91 Display: GO ModeCPIRangeH 35AVRangeL 15VFunctionDynamicConfigure0.000V0.000A0.00wTimer1 0.025Level2 0.00Level1 0.00LOADRS232Fine03/Sep/

PEL-3000 User Manual 92 Program The PEL-3000 can create programs that are designed to step-through up to 16 pre-set load operations. The program

OPERATION 93 program chains.  Program chains need not be executed in order.  There are 16 steps to a program.  There are up to 16 programs to

PEL-3000 User Manual 94 Timing Diagram for Single Step Below is a timing diagram of a single step in a program. On-Time Off-TimeStep test timeStar

OPERATION 95 PROG 01 ~ 16 3. Select a STEP in the selected program. STEP 01 ~ 16 4. Select Memory and select which memory location to load fo

PEL-3000 User Manual 96 8. Choose the P/F-Time (pass/fail time) in seconds.  The P/F-Time refers to the P/F delay time. This delay time includ

OPERATION 97 Create a Program Chain Note Before creating a program chain, make sure a number of programs have already been saved. These will be us